[mkiv] Crank shaft pully BOLT wont open.

[William Kirmil]

I've done the Bump method twice with great results. I put a long  
handle 1/2" ratchet onto the bolt and extended the handle to the floor  
at an angle with a pipe. I bumped the starter and it was done in  
seconds.

On Dec 21, 2009, at 7:19 AM, Roger Marquez wrote:

> This is to break the bolt. The square hole is for a 1/2" breaker  
> bar. Heat will kill the dampner/rubber parts.
>
> ________________________________________
> From: mkiv-bounces at mkiv.com [mkiv-bounces at mkiv.com] On Behalf Of  
> Marcelo Aguirre [maguirre at imowitz.com]
> Sent: Monday, December 21, 2009 10:07 AM
> To: 'The MKIV.com National Mailing List'
> Subject: RE: [mkiv] Crank shaft pully BOLT wont open.
>
> Isn't this to pull the pulley out of the crankshaft once the bolt is  
> loose???
> Hammad needs help loosening the bolt.
> Try heating it up with a blow torch then turn it with a breaker bar.
> I'm gonna need to do this next year to install my new timing belt  
> and ATI damper.
>
> Marcelo
> 97TT, 6spd
>
> -----Original Message-----
> From: mkiv-bounces at mkiv.com [mailto:mkiv-bounces at mkiv.com] On Behalf  
> Of Roger Marquez
> Sent: Saturday, December 19, 2009 6:53 PM
> To: 'The MKIV.com National Mailing List'
> Subject: RE: [mkiv] Crank shaft pully BOLT wont open.
>
> Or
>
> http://www.etooldirect.com/manufacturer/schley-products/schley-64300-lexus-toyota-harmonic-damper-holding-tool.html
>
> Worth every penny IMO.
>
>
>
> -----Original Message-----
> From: mkiv-bounces at mkiv.com [mailto:mkiv-bounces at mkiv.com] On Behalf  
> Of Ryan welch
> Sent: Saturday, December 19, 2009 6:29 PM
> To: The MKIV.com National Mailing List
> Subject: Re: [mkiv] Crank shaft pully BOLT wont open.
>
> Get a long breaker bar and make sure you know what direction the  
> motor turns then lift the car a little off the ground and turn the  
> key to start it, the force breaks free the bolt. Be careful, you DO  
> NOT want to start it up, just bump it over.
>
> --- On Sat, 12/19/09, M. Cheema <cheemahammad at yahoo.com> wrote:
>
>
> From: M. Cheema <cheemahammad at yahoo.com>
> Subject: [mkiv] Crank shaft pully BOLT wont open.
> To: mkiv at mkiv.com
> Date: Saturday, December 19, 2009, 3:28 PM
>
>
> Hello guys....I cant get the crank shaft pully bolt to loosen up.  
> does anyone have any idea as to what i can do?
>
> Thanks.
> Hammad
> 93 JDM 400hp
> 93TT
> 93N/A
>
>
>
> _______________________________________________
> Mkiv mailing list
> Mkiv at mkiv.com
> http://www.mkiv.com/mailman/listinfo/mkiv
>
>
>
>
> _______________________________________________
> Mkiv mailing list
> Mkiv at mkiv.com
> http://www.mkiv.com/mailman/listinfo/mkiv
>
>
> _______________________________________________
> Mkiv mailing list
> Mkiv at mkiv.com
> http://www.mkiv.com/mailman/listinfo/mkiv
>
>
> _________________________________________________
> Scanned on 20 Dec 2009 00:06:06
> Scanned by Erado
>
> Under applicable U.S. Treasury Regulations we are required to inform  
> you that any advice contained in this e-mail message or any  
> attachment hereto is not intended to be used, and cannot be used, to  
> avoid penalties imposed under the Internal Revenue Code.
>
> This email and any attachments are solely for the intended recipient  
> and may contain confidential or privileged information. If you are  
> not the intended recipient, any disclosure, copying, use, or  
> distribution of the information included in this email and any  
> attachments is prohibited. If you have received this communication  
> in error, please notify us by reply e-mail and immediately and  
> permanently delete this email and any attachments.
>
>
> _______________________________________________
> Mkiv mailing list
> Mkiv at mkiv.com
> http://www.mkiv.com/mailman/listinfo/mkiv
>
>
> _______________________________________________
> Mkiv mailing list
> Mkiv at mkiv.com
> http://www.mkiv.com/mailman/listinfo/mkiv